Product Support
Need help finding your model number? Take a look here.
How To Find Your Model Number
Turn over the base of your product to locate the model number as illustrated in the image below.
900 MHz cordless phone with answering system and caller ID
T2151
Manuals & Documentation
Frequently Asked Questions
-
For message recording, your telephone has a Built-in answering system, and it also supports Voicemail service offered by your telephone service provider(subscription is required, and fee may apply).
The main differences between them are:
BUILT-IN ANSWERING SYSTEM VOICEMAIL SERVICE SUPPORTED BY Telephone system Telephone service provider SUBSCRIPTION No Yes FEES No May apply ANSWER INCOMING CALLS •After 3 rings by default.
•It can be changed via handset or the telephone base menu.•Usually after 2 rings.
•It can be changed by contacting your telephone service providerSTORAGE Telephone base Server or System DISPLAY NEW MESSAGE • Handset - XX new messages
• Telephone base - XX new messages• Handset - 
and New voicemail
• Telephone base -
RETRIEVE MESSAGES • Press PLAY/STOP on the telephone base; OR
• Press MENU, and then select Play messages on the handset; OR
•Access remotely with an access code• Press 
on the dialpad, and enter an access number from your telephone service provider.Based on the above information, if you want to...
Use the built-in answering system to record your messages
Your Voicemail service can bundle in your telephone plan. As such, you would need to contact your telephone service provider to disable it.
*TIP: Can I switch back to Voicemail service if I want to?
As long as your telephone plan includes the Voicemail service, you can still re-enable it through your service provider.Use the voicemail service to record your messages
Simply turn off the Built-in answering system at any time, and you can use the Voicemail service only.Use both the Built-in answering system and the Voicemail service to record messages
By default, the Voicemail service is usually set to answer after 2 rings, while your Built-in answering system is set after 3 rings. Please check with your telephone service provider to learn how to set your voicemail settings.Suggest to set your Built-in answering system to answer calls at least 2 rings earlier than your Voicemail service. In other words, if your answering system sets to answer after 3 rings (by default), then you need to set the Voicemail service to answer after 5 rings.
What happened is that if you on a call or the answering system is already recording, and you receive ANOTHER incoming call, then the third caller is able to leave a Voicemail message.
On the other hand, if you are not on a call nor the answering system is recording, the incoming caller can leave a message directly to the Built-in Answering system.
Why is CL flashing in the base message window?
-
During initial setup or after a power loss, you may need to set the time. If the time is not set, CL will be flashing in the base display window.
To set the day and time, complete the following steps:
Step 1: Press TIME/SET. The system will announce the current setting.
Step 2: Press TIME/SET again. The system will announce the current day setting.
Step 3: Press CHANGE on the base until you hear the correct day.
Step 4: Press TIME/SET. The system will announce the current hour setting.
Step 5: Press CHANGE on the base until you hear the correct hour.
Step 6: Press TIME/SET. The system will announce the current minute setting.
NOTE: Pressing and holding the CHANGE button when setting the day and time will increase the minutes or years by 10.
Step 7: Press CHANGE on the base until you hear the correct minute.
Step 8: Press TIME/SET. The system will announce the current year setting.
Step 9: Press CHANGE on the base until you hear the correct year.
Step 10: Press TIME/SET to confirm. The system will announce the new day and time setting followed by a confirmation beep.
Why does the ringer on my handset sound too soft?
-
Tip 1 of 2
You can change the ringer type, or turn the ringer off completely. To change the ringer type, complete the following steps:
Step 1: Make sure the handset is idle (off).
Step 2: Press PROG.
Step 3: Press VOL ▲ until the screen displays RINGER and the current setting.
Step 4: Press PROG. The current setting blinks, and you will hear a sample of the ring.
Step 5: Press VOL ▲ or ▼ to select RINGER 1,2,3,4 or OFF. You will hear a sample of each ring.
Step 6: Press PROG to choose the displayed ringer setting.
-
Tip 2 of 2
You can turn the base ringer on or off:
Step 1: When the phone is not in use, press MENU on the base unit until you hear "Set Base Ringer."
Step 2: Press CHANGE to select ON or OFF.
Step 3: PressTIME/SET to confirm your selection.
Step 4: Press PLAY/STOP to exit programming mode.
Why isn’t CHARGING... shown on the telephone display when I place the handset in the base?
-
Tip 1 of 5
Please make sure that the cords (power and telephone line) are plugged into the channels on the bottom of the base. If the cords are not properly installed, the base will not sit level and the phone may not charge properly. -
Tip 2 of 5
Dirty charge contacts on the telephone base and handset could prevent the batteries from charging. Clean the handset and base charge contacts using a pencil eraser or a cloth to eliminate deposit accumulation. -
Tip 3 of 5
Make sure that the power cord is securely plugged into the base and electrical outlet. Make sure the electrical outlet is not controlled by a wall switch. -
Tip 4 of 5
Make sure that the battery cover is properly secured on the handset. If the battery cover is not correctly installed, it may prevent the handset from charging. -
Tip 5 of 5
If the handset is not responding normally, you may need to reset your telephone system. Complete the following steps to reset the telephone system:
Step 1: Disconnect the power to the telephone base.
Step 2: Disconnect the handset battery.
Step 3: Wait a few minutes and then reconnect the power to the telephone base.
Step 4: Reconnect the handset battery
Step 5: Wait about one minute for the handset to re-establish a link with the telephone base and then test the phone again.
NOTE: After resetting the telephone system, you will need to reset the clock. If the time is not set, CL will be shown on the answering system display.
To set the day and time, confirm that the answering system is turned on and then complete the following steps:
Step 1: Press TIME/SET. The system will announce the current setting.
Step 2: Press TIME/SET again. The system will announce the current day setting.
Step 3: Press CHANGE on the base until you hear the correct day.
Step 4: Press TIME/SET. The system will announce the current hour setting.
Step 5: Press CHANGE on the base until you hear the correct hour.
Step 6: Press TIME/SET. The system will announce the current minute setting.
Step 7: Press CHANGE on the base until you hear the correct minute.
NOTE: Pressing and holding the CHANGE button when setting the day and time will increase the minutes or years by 10.
Step 8: Press TIME/SET. The system will announce the current year setting.
Step 9: Press CHANGE on the base until you hear the correct year.
Step 10: Press TIME/SET to confirm. The system will announce the new day and time setting followed by a confirmation beep.
How do I set the day and time on my telephone answering system?
-
During initial setup or after a power loss, you may need to set the time. If the time is not set, CL will be flashing in the base display window.
To set the day and time, complete the following steps:
Step 1: Press TIME/SET. The system will announce the current setting.
Step 2: Press TIME/SET again. The system will announce the current day setting.
Step 3: Press CHANGE on the base until you hear the correct day.
Step 4: Press TIME/SET. The system will announce the current hour setting.
Step 5: Press CHANGE on the base until you hear the correct hour.
Step 6: Press TIME/SET. The system will announce the current minute setting.
NOTE: Pressing and holding the CHANGE button when setting the day and time will increase the minutes or years by 10.
Step 7: Press CHANGE on the base until you hear the correct minute.
Step 8: Press TIME/SET. The system will announce the current year setting.
Step 9: Press CHANGE on the base until you hear the correct year.
Step 10: Press TIME/SET to confirm. The system will announce the new day and time setting followed by a confirmation beep.
How do I turn the base ringer on or off?
-
You can turn the base ringer on or off:
Step 1: When the phone is not in use, press MENU on the base unit until you hear "Set Base Ringer."
Step 2: Press CHANGE to select ON or OFF.
Step 3: PressTIME/SET to confirm your selection.
Step 4: Press PLAY/STOP to exit programming mode.
Why does my phone display NO CONNECT and beep five times when I press the PHONE button?
-
Tip 1 of 6
Move the handset closer to the base. The operating range may vary with environmental conditions and time of use. There may be places within your environment that a cordless phone will not work well. If the problem only occurs in certain areas of your environment, you can conclude that there is nothing wrong with the phone. Consider trying a phone that operates on a different wireless frequency. -
Tip 2 of 6
Make sure that the power cord is securely plugged into the base and electrical outlet. Make sure the electrical outlet is not controlled by a wall switch. -
Tip 3 of 6
Recradle the handset for 15 seconds, then lift the handset and press PHONE. -
Tip 4 of 6
Since your cordless phone operates like a radio, there may be places within your environment where it may not perform as well as in other areas. In this case, there is nothing wrong with your phone. Try changing the channel while on a call with lots of static. To change the channel, press the CHAN button until the interference has been eliminated. -
Tip 5 of 6
If the handset is not responding normally, you may need to reset your telephone system. Complete the following steps to reset the telephone system:
Step 1: Disconnect the power to the telephone base.
Step 2: Disconnect the handset battery.
Step 3: Wait a few minutes and then reconnect the power to the telephone base.
Step 4: Reconnect the handset battery
Step 5: Wait about one minute for the handset to re-establish a link with the telephone base and then test the phone again.
NOTE: After resetting the telephone system, you will need to reset the clock. If the time is not set, CL will be shown on the answering system display.
To set the day and time, confirm that the answering system is turned on and then complete the following steps:
Step 1: Press TIME/SET. The system will announce the current setting.
Step 2: Press TIME/SET again. The system will announce the current day setting.
Step 3: Press CHANGE on the base until you hear the correct day.
Step 4: Press TIME/SET. The system will announce the current hour setting.
Step 5: Press CHANGE on the base until you hear the correct hour.
Step 6: Press TIME/SET. The system will announce the current minute setting.
Step 7: Press CHANGE on the base until you hear the correct minute.
NOTE: Pressing and holding the CHANGE button when setting the day and time will increase the minutes or years by 10.
Step 8: Press TIME/SET. The system will announce the current year setting.
Step 9: Press CHANGE on the base until you hear the correct year.
Step 10: Press TIME/SET to confirm. The system will announce the new day and time setting followed by a confirmation beep. -
Tip 6 of 6
Other electronic products (i.e., 802.11 wireless networking products, radios, radio towers, pager towers, cell phones, intercoms, room monitors, televisions, personal computers, kitchen appliances and other cordless phones) can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices.
My handset displays NEEDS RECHARGING. What should I do?
-
Tip 1 of 6
When placing the handset in the charging base, confirm that the charge contacts on the handset and base are making a good connection. CHARGING... will display on the handset when it is properly charging.
You should allow 15 hours to fully charge the handset battery. For optimum daily performance, return the handset to its telephone base when not in use. -
Tip 2 of 6
Make sure you are using the battery supplied with your phone. If you are replacing the battery and you need assistance, refer to our VTech Battery Finder. If a battery for your model is unavailable, you can search the internet using the key words cordless phone batteries for an on-line supplier. If you prefer to purchase locally, you can look for a replacement battery at your area consumer electronics retailers. It is recommended that you take your present battery with you to insure your replacement is the correct size and has the correct plug (where applicable) and specifications. -
Tip 3 of 6
Make sure that the power cord is securely plugged into the base and electrical outlet. Make sure the electrical outlet is not controlled by a wall switch. -
Tip 4 of 6
Please make sure that the cords (power and telephone line) are plugged into the channels on the bottom of the base. If the cords are not properly installed, the base will not sit level and the phone may not charge properly. -
Tip 5 of 6
Dirty charge contacts on the telephone base and handset could prevent the batteries from charging. Clean the handset and base charge contacts using a pencil eraser or a cloth to eliminate deposit accumulation. -
Tip 6 of 6
You may need to replace the rechargeable battery, especially if it has been in service for more than one year. To find a replacement, refer to our VTech Battery Finder. If a battery for your model is unavailable, you can search the internet using the key words cordless phone batteries for an on-line supplier. If you prefer to purchase locally, you can look for a replacement battery at your area consumer electronics retailers. It is recommended that you take your present battery with you to insure your replacement is the correct size and has the correct plug (where applicable) and specifications.
Why won’t my Answering System record any messages?
-
Tip 1 of 5
If you have a Telezapper running in "Advanced" Mode, it may interfere with your Telephone Answering System recording messages. You may need to change your Telezapper to "Basic" Mode. Please refer to your User’s Manual for your Telezapper for more information on changing modes. -
Tip 2 of 5
An A will appear in the display window when the Announce Only feature is turned on. In Announce Only mode, callers hear an announcement but cannot leave a message.
To turn Announce Only mode off, please complete the following steps:
Step 1: Press MENU until the system announces, Set Announce only..
Step 2: Press CHANGE until you hear OFF.
Step 3: Press TIME/SET to save.
Step 4: Press PLAY/STOP to exit.
For more information on configuring Announce Only and other features of the answering system, please refer to the Answering System Operation section of the user manual. -
Tip 3 of 5
The volume for your Telephone Answering System may be turned down too low to hear any messages recorded. Press the VOLUME + button to turn up the volume. -
Tip 4 of 5
You may need to reset the Telephone Answering System. Complete the following steps to reset the Telephone Answering System:
Step 1: Disconnect the power to the telephone base.
Step 2: Wait a few minutes and then reconnect the power to the telephone base and charger.
Step 3: Set the day and time. -
Tip 5 of 5
You may have a line problem. To test for a line problem, test your unit at another location such as your neighbor’s or relative’s house. If your unit works at another location, contact your local telephone company.
Why am I not receiving caller ID on my phone?
-
Caller ID and Call Waiting ID are subscription services, available from most local telephone service providers. You must subscribe to these services in order for the features to work on your phone. Contact your local telephone service provider for more information.
In addition, your caller must be calling from an area that supports caller ID.
Both you and your caller’s telephone service provider must use compatible caller ID systems.
If you subscribe to DSL service for this telephone line, DSL filters must be plugged into EVERY phone jack that has a phone. The DSL signal can cause caller ID disruption, static, noise and other issues on your line. DSL filters block the high frequency DSL signals from being transmitted to the telephone. If you are not using the DSL filters provided by the telephone company, this will cause static/noise and possibly caller id issues on your phones.
In most cases, we recommend you connect the plug end of the DSL filter into the telephone jack, then connect a telephone cord between the filter and your phone.
Please contact your service provider to obtain DSL filters and installation information.
Caller ID and Call Waiting ID may not be available for every call. Common reasons are incompatibilities between your and your caller’s service, transmission errors and answering calls before the ID data is received.
How can I improve the sound quality on my cordless phone?
-
If your handset has a CHANNEL (or CHAN) button, press it in order to improve the sound quality. You may need to press the CHANNEL button more than once.
The handset may be out of range. Try moving closer to the base. The handset(s) and base can only communicate over a certain distance which can vary with their placement, the weather and the operating environment of your home/office.
If you subscribe to DSL service for this telephone line, DSL filters must be plugged into EVERY phone jack that has a phone. The DSL signal can cause static/noise, squealing (similar to fax tones), caller ID disruption and other issues on your line. DSL filters block the high frequency DSL signals from being transmitted to the telephone. If you are not using the DSL filters provided by the telephone company, this will cause static/noise and possibly caller id issues on your phones.
In most cases, we recommend you connect the plug end of the DSL filter into the telephone jack, then connect a telephone cord between the filter and your phone.
Please contact your service provider to obtain DSL filters and installation information.
A low battery pack may affect the sound quality. You may need to charge the handset. Also, try repositioning the handset against your ear until the sound quality improves.
Electronic products (i.e., 802.11 wireless networks, radios, radio and pager towers, cell phones, intercoms, room monitors, televisions, personal computers, kitchen appliances and other cordless phones) can cause interference with your cordless phone. Try installing your phone as far away as possible from these types of electronic devices.
Appliances or other cordless phones plugged into the same circuit as the telephone base can cause interference. Try moving the appliances or telephone base to another outlet.
Microwave ovens may operate on the same frequency as your telephone. You may experience static on your telephone while the microwave oven is operating. Do not install your cordless telephone in the same outlet or near the microwave oven.
Disconnect the telephone base from the modular jack and plug in a corded telephone. If calls are still not clear, the problem is probably in the wiring or local service. Contact your local service company (charges may apply).
If your phone shares a power outlet with a modem, or if it is plugged into a shared surged protector, try plugging in the phone (or modem/surge protector) at a different location. If this solves the problem, relocate your phone and modem farther apart from each other, or use separate surge protectors.
The layout of your home or office may be limiting the operating range. Try moving the base to another location, preferably a higher location for better reception. If your telephone base has an adjustable antenna, ensure it is pointing up.
Why is an A showing in the base message window?
-
An A will appear in the display window when the Announce Only feature is turned on. In Announce Only mode, callers hear an announcement but cannot leave a message.
To turn Announce Only mode off, please complete the following steps:
Step 1: Press MENU until the system announces, Set Announce only..
Step 2: Press CHANGE until you hear OFF.
Step 3: Press TIME/SET to save.
Step 4: Press PLAY/STOP to exit.
For more information on configuring Announce Only and other features of the answering system, please refer to the Answering System Operation section of the user manual.
-
Despite your VoIP box shows full signal strength, there could still be no dial tone/ display Line in Use/ etc. This may due to the abnormality of signal and voltage levels. Follow this short video to reset your VoIP box and its connected devices.
(For non-IS8151 series - all other models) https://www.youtube.com/watch?v=mXbXl4froUc&t=25s
(For IS8151-X series) https://www.youtube.com/watch?v=rJ9PNkwBzfE&t=3s
[Background]
• VoIP box connected via SIM/ LAN connection.
• Some VoIP boxes have displays and some not. While displays show steady ON and ready, you might still experience with no dial tone sound/ display Line in Use.[To Reset]
• Some Power off button does not fully power off the unit. It only put the VoIP box in standby mode. To truly power off, unplug the power adapter of your VoIP box.
• Disconnect all devices from the box. After a moment, reconnect your power adapter, and then press power button to turn ON.
• Wait until the VoIP box is steady ON and ready.
• Connect your telephone cable from your Telephone base to your VoIP box.REMINDER!!!
• Make sure you didn't connect the telephone cable from the Telephone wall outlet to VoIP box telephone port!!! Doing so will not damage the device, but it will affect the call function and becomes unusable. This is why you experience no dial tone, Line in Use with busy tone, etc.
• During power outage, your landline phone will not be available since it requires external electric power despite your VoIP box has a backup battery.If this situation persists, contact your VoIP / VoIP box service provider for further support.